Silver Arrow Hobby Jakarta

 
 
Aircraft Electric Beginner ElectricCivillian Scale planeWarbird PlaneAerobatic/F3APlyon raceEDF (Duct Fan)Glider/SailplaneSparepartBalsa StickModel Plywood
Aircraft Engine Beginner PlaneCivillian Scale PlaneWarbirdAerobaticF3A Pattern CompetitionGiant Scale 30cc upJet Engine poweredJet Turbine powered
Helicopter Beginner Coaxial 3-4chSingle Blade 6 ch ElectricNitro Powered
MultiRotor Copter Kit & Camera mountElectronics SystemFPVHobby
Car Electric PoweredNitro PoweredGasoline Powered
Motorcycles 1/5 Superbike1/5 MotorcrossATV
Boat/Sailing/Ship Electric BoatSailing ShipNitro BoatGasoline BoatScale Ship
Engine Nitro Engine 2 stNitro Engine 4 stGasoline EngineTurbine Engine
Muffler AircraftHelicopterCarBoat
Engine Parts Glow Plug/Spark Plug
Heli Parts/option Raptor 30 & 50 sizeSwift 16Swift 620
Propeller Electric PropellerGNX Propeller - 2 bladeGNX Propeller - 3 bladeEngine PropellerBolly PropellerWood PropellerEDF fan/set
Heli Blade/paddle Current or notCurrent or notCurrent or notCurrent or not
Electric Motor AircraftHelicopterCarBoat
ESC Plane/Heli ESCCarBoat
Battery & Charger Lithium Polymer BatteryLiFE batteryChargerBattery accessories
Auto Pilot FMA Auto Pilot
Radio/Transmitter TransmitterReceiverRadio Accessories
Telemetry 2.4g 2 way systemFrsky Telemetry
Servo System Mini/Micro ServoStandart Size ServoServo Accessories
Field Equipment Gas/Nitro Starter system
Float System Aircraft Float System
Electrical System BEC Volt ReducerConnectorServo Extension CableSwitch on/off
Plane Accesories Pilot ModelFuel TankHornEngine MountCovering materialClevisHingesSpinnerLanding gearWheelCarbon Fiber
Heli Accesories Training Skid
Retract System Pneumatic Scale RetractMechanical RetractElectric RetractRetract Accessories
Simulator simulator CD
Fuel Nitro Fuel
Balsa Wood balsa Sheet
Aeromodelling products
 
FrSky DHT-U 2 Way Modul
FrSky DHT-U 2 Way Modul
 
The Two-way Radio System developed by FrSky for Futaba Radio Without Modul System, provides an additional return link that would be used for monitoring the Rx’s voltage, temperature, location, speed and so on.

Call Us for prices

 
 

1. Introduction: 1.1 Compatibility Mode of DHT-U Compatibility V8 _Mode Non-telemetry receivers (V8FR-HV, V8R7-HV, V8R7-SP, V8R4) D_Mode Telemetry receivers (D8R, D8RSP, D6FR, D4FR) 1.2 Specification Operating Voltage Range: 6.0V-13.0V Operating Current: 50mA Output Power: 60mW Resolution: 3072 (>11bit) 1.3 Features 1) All-in-one combination of telemetry module,in-built display and alarm threshold settings 2) DHT-U can be clamped to the transmitter handle/antenna 3) Show in-flight data via in-built display 4) Capable of setting failsafe during flight 5) Firmware upgradable 2 Screen structures 2.1 Main Screen FrSky Logo Data Screen Menu Screen Module ID Version Number 2.2 Data Screen FrSky sensor hub, sensors and D8R telemetry receiver are required if information collecting and processing, model monitoring and data feedback are required. 2.2.1 Data Screen 1 GMT (H/M/S) Fuel Level Voltage A1 Voltage A2 RSSI 2.2.2 Data Screen 2 GMT (H/M/S) Acceleration X/Y/Z Speed RPM Altitude Note: Press Button “R” to change between absolute altitude and relative altitude. 2.2.3 Data Screen 3 GMT (H/M/S) Temperature1 Temperature2 Longitude Latitude 2.3 Menu Screen 2.3.1 Menu Screen 1 V8_Mode/D_Mode Bind/Normal/Range Check Setting Failsafe Note: When V8_Mode is selected, users will have no access to Setting page or Failsafe page. 2.3.2 Menu Screen 2 A1/A2 Voltage Division Ratio: make sure they are programmed in accordance with those of connected voltage sensors Unit Set (selectable): Speed (m/s or MPH) Temperature (Celsius or Fahrenheit) Alarm Set: A1_1/2, A2_1/2, RSSI_1/2 Below are FrSky default values for RSSI, users can change according to their requirements: Alarm Than Value RSSI 1 < 45 2 < 42 2.3.3 Menu Screen 3 Press button B to set failsafe during flight, or others to skip. 3 Set Up 3.1 Installation Process 1) Open the transmitter and find out the battery power supply line, GND and PPM signal line. 2) Solder the battery power supply line, GND and PPM signal line to corresponding wires of DHT-U (RED?V+; BLACK?GND; BROWN?PPM). 3) Clamp DHT-U to the transmitter’s handle or antenna base by provided clamp and screw. 4) Connect the module antenna to DHT-U. 3.2 Bind Procedure 1) Ascertain that the transmitter is in PPM mode. Turn the transmitter off. 2) Turn the transmitter on and enter MENU page, select V8_Mode or D_Mode to work with corresponding receiver you are using (see compatibility chart above). Select Bind. 3) Connect battery to the receiver while holding F/S button on the receiver. The RED LED on the receiver will flash, indicating the binding process is completed. Turn off the transmitter and receiver. 4) Turn the transmitter on and enter MENU page, select Normal. Re-connect battery to the receiver. The RED SOLID LED on the receiver will indicate receiver is receiving commands from the transmitter. After above steps are completed, both the transmitter and receiver are ready to be used. The bind procedure will not have to be repeated unless one of the two is replaced. 3.3 Range Check A pre-flight range check should be done before each flying session. Reflections from nearby metal fences, concrete buildings or trees can cause loss of signal both during the range check and during flight. The following steps are to be followed to perform the range check of the model before flight: 1) Place the model at least 60cm (two feet) above non-metal contaminated ground (e.g. on a wooden bench). 2) The receiver’s antennas should be separated in the model and not touch the ground. Place the module antenna in a vertical position. 3) Turn the transmitter on and enter MENU page, select R-CK, connect battery to the receiver. The effective distance will be decreased to 1/30 of full range. 4) Walk away from the model while simultaneously operating the controls on the transmitter, confirming that all controls operate normally to a distance of 1/30 of the full range. 3.4 Signal Loss Indicator and Failsafe Setting In some special circumstances, such as strong interference, the signal may be lost. When signal is lost in a short period, the receiver continues to try to search for the transmitter, at the same time it keeps the last command from the transmitter, until a new command is received. Failsafe is a useful feature in which all controls move to a preset position whenever the control signal is lost for a period of time. Follow the steps below to set failsafe before flight: 1) Bind the receiver first and turn on both transmitter and receiver; 2) Set all transmitter controls to the desired failsafe position; 3) Press briefly the F/S button of the receiver (less than 1 second), the transmitter module will make a long “beep” (for D8R only) or the GREEN LED of the receiver will flash twice, indicating the failsafe position has been set in the receiver. To disable the failsafe function, re-bind the receiver. Follow the steps below to set failsafe during flight: 1) Bind the receiver first and turn on both transmitter and receiver; 2) Enter MENU page, select F/S to enter failsafe sub-page, press button B to set failsafe at the desired failsafe position during flight. Note: If FrSky DHT-U, sensor hub, sensors and LCD-fdd_lite are applied, please upgrade your telemetry module and D8R receiver with FrSky newly-released ROMs, which can improve the reliability and stability of data feedback after the transmitter’s reset.

2.4GHz Two Way Series Operating Voltage Range: 6.0V-13.0V Operating Current: 50mA Output Power: 60mW Resolution: 3072 (>11bit)

Others Recommended products you should buy :

Sensor Hub and Sensors Sensor Hub and Sensors FrSky Sensor Hub is recommended to connect digital side port (G, TX, RX) of...
Temperature Sensor Temperature Sensor FrSky Temperature Sensor, component for reading engine temperature and transmit...
Rpm Sensor Rpm Sensor Frsky Rpm Sensor will checking and counting your engine rpm, and transmit the...
Fuel gauge sensor Fuel gauge sensor Fuel Sensor will check fuel level on your fuel tanks, it will show many fuel...
GPS Sensor GPS Sensor GPS Sensor will give Director of your model, Longitudinate, and latitude, so...
Variometer Sensor Variometer Sensor Variometer will rate of climb and descent Indicator (RCDI), rate-of-climb...
Triaxial Acceleration Sensor Triaxial Acceleration Sensor 3D G Sensor for topography system, it will sense how the ground level and...
FrSky D8R-II 2 Way Receiver FrSky D8R-II 2 Way Receiver The Two-way Radio System developed by FrSky, It will Transmit Telemetry and...

 
 
FOLLOW US COMPANY INFORMATION SUPPORT MY ACCOUNT  
silver arrow hobby facebook
Phone :
(62)-21-56942803
Phone Hours :
9 am - 5 pm WIB monday - saturday
address :
Salak Masir raya No 9c Tanjung Duren Jakarta Barat Indonesia
 
Map / Location
Store location / Hour
FAQ
Support Page
Technical Articles
RC Dictionary
 
CUSTOMER SERVICE
About Us
Contact Us
Shipping / return
Privacy / Policy
Sign in / Register
Edit Account
Order Status
Order History
View Cart
Check Out
10 visitors online

 
visa card - aeromodelling jakartamastercard- aeromodelling shopklik bca - silver arrow hobbybank mandiri - jakarta indonesiapanin bank - jakarta indonesiaCIMB Niaga - Indonesia aeromodelling Web design (2011) By PT. Puri Global Internusa Jakarta Indonesia